• Possible Cause
    Action
    Drum has solid build-ups Clean the drum, ensuring all solids are removed from sides and base of vanes and change filter pads
    Damaged motor bearing Consider adding a pre-filter or compact cyclone. Grinding operations will require shorter service intervals because of the grinding dust that can be taken into the unit along with the oil mist. Check motor bearing and replace motor if required.
    Used on acidic substances Do not use on high acidic substances
    Drum loose Disassemble drum from unit, and then re-connect and re-tighten drum
    Drum is out of balance Return to Filtermist for re-balancing
  • Possible Cause
    Action
    Incoming air to unit is higher than 60°C Fit T piece and airflow regulator to reduce air temperature to allow mist/steam to condense
    T Piece with airflow regulator not allowing fresh air to help condense steam Open airflow regulator to allow fresh air to be pulled into operation
  • Possible Cause
    Action
    Drum is rotating in wrong direction Check rotation of drum – anti-clockwise when viewed from inlet
    Re-position and clean the drain hose. If motor ‘kicks’ in one direction of rotation, the drum will be spinning in the opposite
    Drain hose is blocked, kinked or submerged Remove blockage or kink, ensure hose is not submerged
    Excessive extraction Re-position extraction point or fit splashguard
    Fume could be oil smoke Fit High Efficiency Afterfilter. Do not use on heavy smoke extraction.
    Unit attempting to filter in a dry dust application Do not use Filtermist product on dry dust applications
    Attempting to use Filtermist unit on high pressure neat oil applications (over 10 bar) Fit Fusion filter or High Efficiency filter. If still an issue alternative solution required
  • Possible Cause
    Action
    Blocked inlet Clean inlet swarf arrestor
    Afterfilter is blocked Change Afterfilter – (recommended every 3-6 months)
    Unit needs servicing Contact Filtermist Local Distributor (recommended Service intervals of 6 months or 1000 hours – whichever earlier)
    Kinks in ducting Ensure no kinks in ducting

    Ensure that the ducting has no “U” bends without an oil drainaway at the bottom of the “U”, as this will cause oil to build up and block airflow
    Pre-filter blocked If unit has a pre-filter, to check that it is not the pre-filter blocking the air, remove to test the airflow; if the airflow returns to correct levels, order replacement pads, or clean the recyclable pre-filter using a parts washer
    Equipment requiring extraction not adequately enclosed The unit will have an especially difficult job, and must not usually be used on high velocity applications such as grinding, and should be tested to ensure the unenclosed equipment’s mist is safely extracted
    Drum spinning the wrong direction Check the rotation of the drum from above or below the Filtermist unit.

    Ensure the red directional arrow is followed when the unit is speeding down or speeding up (as you cannot tell which direction the drum is spinning when the unit is operating at full speed).

    If the drum is turning in the wrong direction, change two of the three phase wires around (from L1, L2, L3).
  • Possible Cause
    Action
    Overload setting incorrect Reset or replace overload (see electrical info chart) in product manual
  • Possible Cause
    Action
    Kinks in oil return hose Straighten or replace oil return hose
    Oil return hose submerged in oil Remove oil return hose from oil, either by connecting to higher location, or cutting to suit to be above level of oil
  • Possible Cause
    Action
    Equipment not working correctly Maintenance schedule with local distributor to be advised. Check above for ‘Unit is not extracting’. Fit Afterfilter if not already fitted
    Not installed correctly Request an ‘LEV’ (Local Exhaust Ventilation) test to ensure setup is working as required, including oil mist readings at 10 and 1 micron in factory ambient air using DustTrak or similar. Test near gaps and air intakes/outlets of the extraction equipment and machine tools to check contaminant is not escaping into the air. Action the findings of the specific report
    LEV equipment not being operated correctly Train operators to turn on LEV equipment at appropriate times, close doors of machines when not in use, keep guards in place. Train on the effects of oil mist contamination on human health
    Extraction point above the workpiece or close to operator Relocate Filtermist unit extraction point as far away from the machining operation as practicably possible
    The smell could be created by another application that does not have mist extraction on, such as another machine tool or an open oil tank, or one that does have mist extraction on, but it needs servicing. Identify all potential sources and fit or service extraction as necessary
  • Possible Cause
    Action
    The Filtermist is successful in removing mist and steam from applications up to 60º Celsius If the temperature is higher than this, then you must try to cool the mist before it reaches the unit

    Always consider specifying Stainless Steel units when dealing with higher temperatures or highly corrosive detergents

    Where ambient air needs to be taken into the system to help cool the mist or steam, T-pieces can be used with airflow regulators to control the amount of ambient air being used

    -

    Filtermist provides oil mist collectors in over 60 countries worldwide

    language
    Europe
    language
    Africa
    Asia
    Middle East
    UK & Ireland
    language
    North America
    Latin America
    Australasia